How to Prepare for Woodshop Projects
When undertaking woodshop projects, using a plan for each particular project can provide you with some benefits and allow you to create something from scratch. These plans can be for something as simple as a magazine rack or something as complex as a large piece of furniture. Woodshop projects allow you to experience lots of versatility.
Woodshop Projects: The Importance of Following a Plan
You can attempt to complete woodshop projects without plans, but there will be some difficulties you’re likely to encounter. The first issue that comes up is that woodshop projects might seem easy, but they can turn out to be significantly more complicated than you initially thought. Having a robust set of plans on hand will go a long way towards making even a complex project go smoothly. The plans should include all the steps you need in order to complete the project, in addition to a list of required materials and tools.
Many people who undertake woodworking projects without plans might not have or realize that they need a particular piece of equipment to complete the project. This will cause delays in the project and can end up being expensive. It’s also a good idea to have plans because it will provide you with a systematic guide to getting the job done.
Different projects will require different skill levels. Knowing your skill level and the skill standards of a project will be substantial. Using a set of plans can also go a long way regarding ensuring that you’ll be able to plan out your project around your budget and that you can choose a project that you can afford.
Woodworking Problems you may run into during a Project
There are many woodworking issues you should keep in mind when working on a project. Some of these matters will vary based on your skill level or the type of wood you use, so it’s best that you have some knowledge regarding any potential issue that can come up during a project. First off, we’ll discuss miter corners. Even the most well-cut halves of a mitered corner will not always line up the way you planned. Because wood is a material that’s constantly adjusting to the fluctuations in the humidity in the air, or because of imperfections in the cut of the grain, mitered corners of your boards may not always align precisely.
A ruined stained finish from glue run out can happen. When you apply too much wood glue, it can result in adhesive run out. This can be an issue for projects that require a stained finish because the pores of the exposed areas can become clogged with the glue and end up preventing the stain from seeping into the pores. The result will be a piece of wood that has a splotchy and uneven look.
Be careful of saw blade burn outs. When you work with fine hardwoods, your table saw blade can burn on the cut edge of the wood, and this can end up being a real problem. You’ll probably be tempted to sand or scrape off the burn marks, but it’s better that you try to prevent burns from the get go. By making a few adjustments to your saw, you’ll be able to eliminate most burns so be sure to read the instruction manual for your saw, before starting your woodworking project.
No Brainer Safety Tips for Woodworking
The most important rule when it comes to woodworking is always to wear your safety gear. Safety goggles will top this list; however, you may also need to wear protective gloves and ears plugs, depending on the project.
Whenever you’re working in your wood shop, remember that you should avoid wearing loose fitting clothes. You should instead wear clothes that feel comfortable, but that can also protect you from wayward wood chips that can result in cutting your skin. Also, be sure to remove any jewelry.
Drinking and woodworking can make a dangerous combination. While it may seem harmless to drink a few beers while working in your shop, try to avoid temptation until you’re finished.
Whenever a blade change or bit change is needed, always disconnect the power tool from electricity before making the change.
Another good safety tip is always to check the stock you are preparing to cut for metals before you begin a cut. Rapidly spinning blades and nails aren’t a good mix. Not only can it damage your machinery but the kickback can cause injury.
Power tools for woodworking are designed so that the direction of the piece of wood moves through a tool
When working with a saw, never put your hands near the blade, especially when you’re trying to remove cut off or waste. Instead, wait until the blade has stopped moving and use a push stick or piece of scrap wood to eliminate the waste.